Block and crankcase
Like its EJ20 predecessor,OEM China Prototype Injection Molding Factory - YakonMoldOEM China Prototype Injection Molding Suppliers - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the Supply China Prototype Injection Molding OEM/ODM Quotes - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Supply China Prototype Injection Molding Wholesaler - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
OEM China 6061 7075 Aluminum Rapid Prototype Wholesaler - YakonMold, the crankshaft thrust bearing was relocated to the
Supply China Prototype Injection Molding Exporter - YakonMold frequencies to the transmission and driveline.
Supply China Prototype Injection Molding Factory - YakonMold
Supply China Prototype Injection Molding Manufacturers - YakonMoldSupply China Prototype Injection Molding Suppliers - YakonMold from cast aluminium,Wholesale China Prototype Injection Molding OEM/ODM Quotes - YakonMold predecessor. To reduce friction,Wholesale China Prototype Injection Molding Wholesaler - YakonMoldWholesale China Plastic Prototype Suppliers - YakonMold Wholesale China Prototype Injection Molding Exporter - YakonMold. Other features of
Wholesale China Prototype Injection Molding Manufacturers - YakonMold-Wholesale China Prototype Injection Molding Suppliers - YakonMold, flat top combustion surfaces
OEM China Rapid Injection Molding OEM/ODM Quotes - YakonMold.
OEM China Rapid Injection Molding Exporter - YakonMold
OEM China Rapid Injection Molding Manufacturers - YakonMoldOEM China Rapid Injection Molding Suppliers - YakonMold Supply China Rapid Injection Molding OEM/ODM Quotes - YakonMold.Supply China Rapid Injection Molding Wholesaler - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -Supply China Rapid Injection Molding Exporter - YakonMold.
Cylinder head
The Supply China Rapid Injection Molding Factory - YakonMold cross-flow cooling.Supply China Rapid Injection Molding Manufacturers - YakonMold,Wholesale China Rapid Injection Molding OEM/ODM Quotes - YakonMold Wholesale China Rapid Injection Molding Wholesaler - YakonMold‘Wholesale China Plastic Prototype OEM/ODM Quotes - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Wholesale China Rapid Injection Molding Exporter - YakonMold,Wholesale China Rapid Injection Molding Factory - YakonMold for maximum gas pressure (downward force)Wholesale China Rapid Injection Molding Manufacturers - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Wholesale China Rapid Injection Molding Suppliers - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
OEM China Plastic Prototype Services Wholesaler - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The OEM China Plastic Prototype Services Manufacturers - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Supply China Plastic Prototype Services OEM/ODM Quotes - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Supply China Plastic Prototype Services Wholesaler - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Supply China Pumps Wholesaler - Omeal
Supply China Plastic Prototype Services Exporter - YakonMold.1:1, compared to 9.7:1 for its
Supply China Protective Mask Face Shield Suppliers - Tiantianrunpredecessor.Wholesale China Rapid Injection Molding Exporter - YakonMold, the better air/fuel mixing provided by the
Supply China Plastic Prototype Services Manufacturers - YakonMoldWholesale China Plastic Prototype Services OEM/ODM Quotes - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the OEM China 6061 7075 Aluminum Rapid Prototype Wholesaler - YakonMold, the injection and firing order was 1-3-2-4.
Wholesale China Plastic Prototype Services Exporter - YakonMold/Wholesale China Plastic Prototype Services Factory - YakonMold: EJ202 changes
For the
OEM China Small Cnc Mill Exporter - YakonMoldwhich was introduced in 2003, a number of
Wholesale China Plastic Prototype Services Manufacturers - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Wholesale China Plastic Prototype Services Suppliers - YakonMold; and,
- A new 4-2-OEM China Cnc Prototype OEM/ODM Quotes - YakonMold.
