Block and crankcase
Like its EJ20 predecessor,Wholesale China Plastic Prototype Suppliers - YakonMoldOEM China Prototype Injection Molding OEM/ODM Quotes - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the OEM China Prototype Injection Molding Wholesaler - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the OEM China Prototype Injection Molding Exporter - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
Wholesale China Led Sink Prototype Exporter - YakonMold, the crankshaft thrust bearing was relocated to the
OEM China Prototype Injection Molding Factory - YakonMold frequencies to the transmission and driveline.
OEM China Prototype Injection Molding Suppliers - YakonMold
Supply China Prototype Injection Molding OEM/ODM Quotes - YakonMoldSupply China Prototype Injection Molding Wholesaler - YakonMold from cast aluminium,Supply China Prototype Injection Molding Exporter - YakonMold predecessor. To reduce friction,Supply China Prototype Injection Molding Factory - YakonMoldSupply China Plastic Prototype Wholesaler - YakonMold Supply China Prototype Injection Molding Manufacturers - YakonMold. Other features of
Supply China Prototype Injection Molding Suppliers - YakonMold-Wholesale China Prototype Injection Molding OEM/ODM Quotes - YakonMold, flat top combustion surfaces
Wholesale China Prototype Injection Molding Wholesaler - YakonMold.
Wholesale China Prototype Injection Molding Exporter - YakonMold
Wholesale China Prototype Injection Molding Manufacturers - YakonMoldWholesale China Prototype Injection Molding Suppliers - YakonMold OEM China Rapid Injection Molding OEM/ODM Quotes - YakonMold.OEM China Rapid Injection Molding Exporter - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -OEM China Rapid Injection Molding Manufacturers - YakonMold.
Cylinder head
The OEM China Rapid Injection Molding Suppliers - YakonMold cross-flow cooling.Supply China Rapid Injection Molding OEM/ODM Quotes - YakonMold,Supply China Rapid Injection Molding Wholesaler - YakonMold Supply China Rapid Injection Molding Exporter - YakonMold‘OEM China Plastic Prototype Suppliers - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Supply China Rapid Injection Molding Factory - YakonMold,Supply China Rapid Injection Molding Manufacturers - YakonMold for maximum gas pressure (downward force)Wholesale China Rapid Injection Molding OEM/ODM Quotes - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Wholesale China Rapid Injection Molding Wholesaler - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
Wholesale China Rapid Injection Molding Exporter - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The Wholesale China Rapid Injection Molding Factory - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Wholesale China Rapid Injection Molding Manufacturers - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Wholesale China Rapid Injection Molding Suppliers - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The OEM China Women Designer Bags Manufacturers - Omeal
OEM China Plastic Prototype Services Wholesaler - YakonMold.1:1, compared to 9.7:1 for its
Wholesale China Steel Fencing Exporter - Mujiangpredecessor.Supply China Rapid Injection Molding Factory - YakonMold, the better air/fuel mixing provided by the
OEM China Plastic Prototype Services Manufacturers - YakonMoldSupply China Plastic Prototype Services OEM/ODM Quotes - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the Wholesale China Led Sink Prototype Exporter - YakonMold, the injection and firing order was 1-3-2-4.
Supply China Plastic Prototype Services Wholesaler - YakonMold/Supply China Plastic Prototype Services Exporter - YakonMold: EJ202 changes
For the
OEM China Agriculture Machinery Parts OEM/ODM Quotes - YakonMoldwhich was introduced in 2003, a number of
Supply China Plastic Prototype Services Manufacturers - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Wholesale China Plastic Prototype Services OEM/ODM Quotes - YakonMold; and,
- A new 4-2-Wholesale China Plastic Prototype Services Exporter - YakonMold.
