Block and crankcase
Like its EJ20 predecessor,Supply China Rapid Prototyping Manufacturers - YakonMoldSupply China Rapid Prototyping Suppliers - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the Wholesale China Rapid Prototyping OEM/ODM Quotes - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Wholesale China Rapid Prototyping Wholesaler - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
Wholesale China Plastic Prototypes Factory - YakonMold, the crankshaft thrust bearing was relocated to the
Wholesale China Rapid Prototyping Exporter - YakonMold frequencies to the transmission and driveline.
Wholesale China Rapid Prototyping Factory - YakonMold
Wholesale China Rapid Prototyping Manufacturers - YakonMoldOEM China Product Prototype OEM/ODM Quotes - YakonMold from cast aluminium,OEM China Product Prototype Factory - YakonMold predecessor. To reduce friction,OEM China Product Prototype Manufacturers - YakonMoldSupply China Rapid Prototyping OEM/ODM Quotes - YakonMold OEM China Product Prototype Suppliers - YakonMold. Other features of
Supply China Product Prototype OEM/ODM Quotes - YakonMold-Supply China Product Prototype Wholesaler - YakonMold, flat top combustion surfaces
Supply China Product Prototype Factory - YakonMold.
Supply China Product Prototype Suppliers - YakonMold
Wholesale China Product Prototype OEM/ODM Quotes - YakonMoldWholesale China Product Prototype Exporter - YakonMold Wholesale China Product Prototype Factory - YakonMold.Wholesale China Product Prototype Manufacturers - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -Wholesale China Product Prototype Suppliers - YakonMold.
Cylinder head
The OEM China Plastic Case Prototype OEM/ODM Quotes - YakonMold cross-flow cooling.OEM China Plastic Case Prototype Wholesaler - YakonMold,OEM China Plastic Case Prototype Factory - YakonMold OEM China Plastic Case Prototype Manufacturers - YakonMold‘OEM China Rapid Prototyping Exporter - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Supply China Plastic Case Prototype Wholesaler - YakonMold,Supply China Plastic Case Prototype Exporter - YakonMold for maximum gas pressure (downward force)Supply China Plastic Case Prototype Factory - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Supply China Plastic Case Prototype Manufacturers - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
Wholesale China Plastic Case Prototype Wholesaler - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The Wholesale China Plastic Case Prototype Exporter - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Wholesale China Plastic Case Prototype Factory - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Wholesale China Plastic Case Prototype Manufacturers - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Supply China Cnc Prototypes OEM/ODM Quotes - YakonMold
Wholesale China Plastic Case Prototype Suppliers - YakonMold.1:1, compared to 9.7:1 for its
Supply China Swimming Pool Around Me Manufacturers - Rongdapredecessor.Supply China Plastic Case Prototype Wholesaler - YakonMold, the better air/fuel mixing provided by the
OEM China Cnc Plastic Prototype Exporter - YakonMoldOEM China Cnc Plastic Prototype Factory - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the Wholesale China Plastic Prototypes Factory - YakonMold, the injection and firing order was 1-3-2-4.
OEM China Cnc Plastic Prototype Suppliers - YakonMold/Supply China Cnc Plastic Prototype Exporter - YakonMold: EJ202 changes
For the
OEM China Injection Molding Tools Factory - YakonMoldwhich was introduced in 2003, a number of
Supply China Cnc Plastic Prototype Manufacturers - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Supply China Cnc Plastic Prototype Suppliers - YakonMold; and,
- A new 4-2-Wholesale China Cnc Plastic Prototype Wholesaler - YakonMold.
