Block and crankcase
Like its EJ20 predecessor,OEM China Hot Runner Plastic Injection Mould Factory - YakonMoldOEM China Hot Runner Plastic Injection Mould Manufacturers - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the OEM China Hot Runner Plastic Injection Mould Suppliers - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Supply China Hot Runner Plastic Injection Mould OEM/ODM Quotes - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
Wholesale China Aluminium Parts Wholesaler - YakonMold, the crankshaft thrust bearing was relocated to the
Supply China Hot Runner Plastic Injection Mould Wholesaler - YakonMold frequencies to the transmission and driveline.
Supply China Hot Runner Plastic Injection Mould Exporter - YakonMold
Supply China Hot Runner Plastic Injection Mould Factory - YakonMoldSupply China Hot Runner Plastic Injection Mould Manufacturers - YakonMold from cast aluminium,Supply China Hot Runner Plastic Injection Mould Suppliers - YakonMold predecessor. To reduce friction,Wholesale China Hot Runner Plastic Injection Mould Wholesaler - YakonMoldWholesale China Machined Parts Suppliers - YakonMold Wholesale China Hot Runner Plastic Injection Mould Exporter - YakonMold. Other features of
Wholesale China Hot Runner Plastic Injection Mould Factory - YakonMold-Wholesale China Hot Runner Plastic Injection Mould Manufacturers - YakonMold, flat top combustion surfaces
Wholesale China Hot Runner Plastic Injection Mould Suppliers - YakonMold.
OEM China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold
OEM China Metal Injection Moulding Part Wholesaler - YakonMoldOEM China Metal Injection Moulding Part Exporter - YakonMold OEM China Metal Injection Moulding Part Factory - YakonMold.OEM China Metal Injection Moulding Part Manufacturers - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -OEM China Metal Injection Moulding Part Suppliers - YakonMold.
Cylinder head
The Supply China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold cross-flow cooling.Supply China Metal Injection Moulding Part Wholesaler - YakonMold,Supply China Metal Injection Moulding Part Exporter - YakonMold Supply China Metal Injection Moulding Part Factory - YakonMold‘Wholesale China Machined Parts Factory - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Supply China Metal Injection Moulding Part Manufacturers - YakonMold,Wholesale China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold for maximum gas pressure (downward force)Wholesale China Metal Injection Moulding Part Wholesaler - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Wholesale China Metal Injection Moulding Part Exporter - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
Wholesale China Metal Injection Moulding Part Factory - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The Wholesale China Metal Injection Moulding Part Manufacturers - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Wholesale China Metal Injection Moulding Part Suppliers - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.OEM China Metal Injection Moulding Wholesaler - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Wholesale China Necklace Suppliers - Omeal
OEM China Metal Injection Moulding Exporter - YakonMold.1:1, compared to 9.7:1 for its
Wholesale China Ningbo Baby Diapers Factory - Hexingpredecessor.Supply China Metal Injection Moulding Part Manufacturers - YakonMold, the better air/fuel mixing provided by the
OEM China Metal Injection Moulding Factory - YakonMoldOEM China Metal Injection Moulding Manufacturers - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the Wholesale China Aluminium Parts Wholesaler - YakonMold, the injection and firing order was 1-3-2-4.
OEM China Metal Injection Moulding Suppliers - YakonMold/Supply China Metal Injection Moulding OEM/ODM Quotes - YakonMold: EJ202 changes
For the
OEM China Die Cast Aluminum Alloys OEM/ODM Quotes - YakonMoldwhich was introduced in 2003, a number of
Supply China Metal Injection Moulding Wholesaler - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Supply China Metal Injection Moulding Exporter - YakonMold; and,
- A new 4-2-Supply China Metal Injection Moulding Factory - YakonMold.
