Block and crankcase
Like its EJ20 predecessor,Supply China Machined Parts Factory - YakonMoldSupply China Machined Parts Manufacturers - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the Supply China Machined Parts Suppliers - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Wholesale China Machined Parts OEM/ODM Quotes - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
Wholesale China Abs Machined Parts Suppliers - YakonMold, the crankshaft thrust bearing was relocated to the
Wholesale China Machined Parts Wholesaler - YakonMold frequencies to the transmission and driveline.
Wholesale China Machined Parts Exporter - YakonMold
Wholesale China Machined Parts Factory - YakonMoldWholesale China Machined Parts Manufacturers - YakonMold from cast aluminium,Wholesale China Machined Parts Suppliers - YakonMold predecessor. To reduce friction,OEM China Hot Runner Plastic Injection Mould OEM/ODM Quotes - YakonMoldOEM China Machined Parts Suppliers - YakonMold OEM China Hot Runner Plastic Injection Mould Wholesaler - YakonMold. Other features of
OEM China Hot Runner Plastic Injection Mould Exporter - YakonMold-OEM China Hot Runner Plastic Injection Mould Factory - YakonMold, flat top combustion surfaces
OEM China Hot Runner Plastic Injection Mould Manufacturers - YakonMold.
OEM China Hot Runner Plastic Injection Mould Suppliers - YakonMold
Supply China Hot Runner Plastic Injection Mould OEM/ODM Quotes - YakonMoldSupply China Hot Runner Plastic Injection Mould Wholesaler - YakonMold Supply China Hot Runner Plastic Injection Mould Exporter - YakonMold.Supply China Hot Runner Plastic Injection Mould Factory - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -Supply China Hot Runner Plastic Injection Mould Manufacturers - YakonMold.
Cylinder head
The Supply China Hot Runner Plastic Injection Mould Suppliers - YakonMold cross-flow cooling.Wholesale China Hot Runner Plastic Injection Mould Wholesaler - YakonMold,Wholesale China Hot Runner Plastic Injection Mould Exporter - YakonMold Wholesale China Hot Runner Plastic Injection Mould Factory - YakonMold‘OEM China Machined Parts Exporter - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Wholesale China Hot Runner Plastic Injection Mould Manufacturers - YakonMold,Wholesale China Hot Runner Plastic Injection Mould Suppliers - YakonMold for maximum gas pressure (downward force)OEM China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The OEM China Metal Injection Moulding Part Wholesaler - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
OEM China Metal Injection Moulding Part Exporter - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The OEM China Metal Injection Moulding Part Factory - YakonMold-point sequential fuel injection and
centrally located spark plugs. The OEM China Metal Injection Moulding Part Manufacturers - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.OEM China Metal Injection Moulding Part Suppliers - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Supply China Nappa Shoes Wholesaler - Omeal
Supply China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold.1:1, compared to 9.7:1 for its
Wholesale China Indoor Water Storage Tank Factory - Rongdapredecessor.Wholesale China Hot Runner Plastic Injection Mould Manufacturers - YakonMold, the better air/fuel mixing provided by the
Supply China Metal Injection Moulding Part Wholesaler - YakonMoldSupply China Metal Injection Moulding Part Exporter - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the Wholesale China Abs Machined Parts Suppliers - YakonMold, the injection and firing order was 1-3-2-4.
Supply China Metal Injection Moulding Part Factory - YakonMold/Supply China Metal Injection Moulding Part Manufacturers - YakonMold: EJ202 changes
For the
Supply China Designer Shoes Manufacturers - Omealwhich was introduced in 2003, a number of
Wholesale China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Wholesale China Metal Injection Moulding Part Wholesaler - YakonMold; and,
- A new 4-2-Wholesale China Metal Injection Moulding Part Exporter - YakonMold.
