Block and crankcase
Like its EJ20 predecessor,Supply China Machined Parts Manufacturers - YakonMoldSupply China Machined Parts Suppliers - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the Wholesale China Machined Parts OEM/ODM Quotes - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Wholesale China Machined Parts Wholesaler - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
OEM China Aluminium Parts OEM/ODM Quotes - YakonMold, the crankshaft thrust bearing was relocated to the
Wholesale China Machined Parts Exporter - YakonMold frequencies to the transmission and driveline.
Wholesale China Machined Parts Factory - YakonMold
Wholesale China Machined Parts Manufacturers - YakonMoldWholesale China Machined Parts Suppliers - YakonMold from cast aluminium,OEM China Hot Runner Plastic Injection Mould OEM/ODM Quotes - YakonMold predecessor. To reduce friction,OEM China Hot Runner Plastic Injection Mould Wholesaler - YakonMoldSupply China Machined Parts OEM/ODM Quotes - YakonMold OEM China Hot Runner Plastic Injection Mould Exporter - YakonMold. Other features of
OEM China Hot Runner Plastic Injection Mould Factory - YakonMold-OEM China Hot Runner Plastic Injection Mould Manufacturers - YakonMold, flat top combustion surfaces
OEM China Hot Runner Plastic Injection Mould Suppliers - YakonMold.
Supply China Hot Runner Plastic Injection Mould OEM/ODM Quotes - YakonMold
Supply China Hot Runner Plastic Injection Mould Wholesaler - YakonMoldSupply China Hot Runner Plastic Injection Mould Exporter - YakonMold Supply China Hot Runner Plastic Injection Mould Factory - YakonMold.Supply China Hot Runner Plastic Injection Mould Manufacturers - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -Supply China Hot Runner Plastic Injection Mould Suppliers - YakonMold.
Cylinder head
The Wholesale China Hot Runner Plastic Injection Mould Wholesaler - YakonMold cross-flow cooling.Wholesale China Hot Runner Plastic Injection Mould Exporter - YakonMold,Wholesale China Hot Runner Plastic Injection Mould Factory - YakonMold Wholesale China Hot Runner Plastic Injection Mould Manufacturers - YakonMold‘OEM China Machined Parts Factory - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Wholesale China Hot Runner Plastic Injection Mould Suppliers - YakonMold,OEM China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold for maximum gas pressure (downward force)OEM China Metal Injection Moulding Part Wholesaler - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The OEM China Metal Injection Moulding Part Exporter - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
OEM China Metal Injection Moulding Part Factory - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The OEM China Metal Injection Moulding Part Manufacturers - YakonMold-point sequential fuel injection and
centrally located spark plugs. The OEM China Metal Injection Moulding Part Suppliers - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Supply China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Wholesale China Toe Shoes Manufacturers - Omeal
Supply China Metal Injection Moulding Part Wholesaler - YakonMold.1:1, compared to 9.7:1 for its
Supply China Beautiful Swimming Pool Manufacturers - Rongdapredecessor.Wholesale China Hot Runner Plastic Injection Mould Suppliers - YakonMold, the better air/fuel mixing provided by the
Supply China Metal Injection Moulding Part Exporter - YakonMoldSupply China Metal Injection Moulding Part Factory - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the OEM China Aluminium Parts OEM/ODM Quotes - YakonMold, the injection and firing order was 1-3-2-4.
Supply China Metal Injection Moulding Part Manufacturers - YakonMold/Wholesale China Metal Injection Moulding Part OEM/ODM Quotes - YakonMold: EJ202 changes
For the
Supply China Accessory Factory Exporter - Omealwhich was introduced in 2003, a number of
Wholesale China Metal Injection Moulding Part Wholesaler - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Wholesale China Metal Injection Moulding Part Exporter - YakonMold; and,
- A new 4-2-Wholesale China Metal Injection Moulding Part Factory - YakonMold.
