Block and crankcase
Like its EJ20 predecessor,OEM China Double Color Injection Mould OEM/ODM Quotes - YakonMoldOEM China Double Color Injection Mould Wholesaler - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the OEM China Double Color Injection Mould Exporter - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the OEM China Double Color Injection Mould Factory - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
Supply China Plastic Injection Mould Makers OEM/ODM Quotes - YakonMold, the crankshaft thrust bearing was relocated to the
OEM China Double Color Injection Mould Manufacturers - YakonMold frequencies to the transmission and driveline.
OEM China Double Color Injection Mould Suppliers - YakonMold
Supply China Double Color Injection Mould Wholesaler - YakonMoldSupply China Double Color Injection Mould Exporter - YakonMold from cast aluminium,Supply China Double Color Injection Mould Factory - YakonMold predecessor. To reduce friction,Supply China Double Color Injection Mould Manufacturers - YakonMoldWholesale China Custom Plastic Injection Exporter - YakonMold Supply China Double Color Injection Mould Suppliers - YakonMold. Other features of
Wholesale China Double Color Injection Mould OEM/ODM Quotes - YakonMold-Wholesale China Double Color Injection Mould Wholesaler - YakonMold, flat top combustion surfaces
Wholesale China Double Color Injection Mould Exporter - YakonMold.
Wholesale China Double Color Injection Mould Factory - YakonMold
Wholesale China Double Color Injection Mould Manufacturers - YakonMoldWholesale China Double Color Injection Mould Suppliers - YakonMold OEM China Silicone Injection Mould OEM/ODM Quotes - YakonMold.OEM China Silicone Injection Mould Exporter - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -OEM China Silicone Injection Mould Factory - YakonMold.
Cylinder head
The OEM China Silicone Injection Mould Manufacturers - YakonMold cross-flow cooling.OEM China Silicone Injection Mould Suppliers - YakonMold,Supply China Silicone Injection Mould OEM/ODM Quotes - YakonMold Supply China Silicone Injection Mould Wholesaler - YakonMold‘Wholesale China Custom Plastic Injection OEM/ODM Quotes - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.Supply China Silicone Injection Mould Exporter - YakonMold,Supply China Silicone Injection Mould Factory - YakonMold for maximum gas pressure (downward force)Supply China Silicone Injection Mould Suppliers - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Wholesale China Silicone Injection Mould Wholesaler - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
Wholesale China Silicone Injection Mould Exporter - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The Wholesale China Silicone Injection Mould Factory - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Wholesale China Silicone Injection Mould Manufacturers - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Wholesale China Silicone Injection Mould Suppliers - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Supply China Cnc Machining Parts Machine Assembly Wholesaler - YakonMold
OEM China Injection Moulding Parts Wholesaler - YakonMold.1:1, compared to 9.7:1 for its
Supply China Metal Parts Wholesaler - Mujiangpredecessor.Supply China Silicone Injection Mould Exporter - YakonMold, the better air/fuel mixing provided by the
OEM China Injection Moulding Parts Exporter - YakonMoldOEM China Injection Moulding Parts Factory - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the Supply China Plastic Injection Mould Makers OEM/ODM Quotes - YakonMold, the injection and firing order was 1-3-2-4.
OEM China Injection Moulding Parts Manufacturers - YakonMold/OEM China Injection Moulding Parts Suppliers - YakonMold: EJ202 changes
For the
Supply China Aluminum Cast Wholesaler - YakonMoldwhich was introduced in 2003, a number of
Supply China Injection Moulding Parts OEM/ODM Quotes - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-Supply China Injection Moulding Parts Wholesaler - YakonMold; and,
- A new 4-2-Supply China Injection Moulding Parts Exporter - YakonMold.
