Block and crankcase
Like its EJ20 predecessor,Wholesale China Custom Plastic Injection Wholesaler - YakonMoldWholesale China Custom Plastic Injection Exporter - YakonMold aluminium alloy block with 92.0 mm bores – with cast iron dry-type cylinder
liners – and a 75.0 mm stroke for a capacity of 1994 cc. The cylinder block
for the Wholesale China Custom Plastic Injection Factory - YakonMold-deck design whereby the cylinder
walls were supported at the three and nine o’clock positions.
The
crankcase for the Wholesale China Custom Plastic Injection Manufacturers - YakonMold flywheel housing was cast with the crankcase for increased rigidity. For the
OEM China Plastic Injection Mould Makers Wholesaler - YakonMold, the crankshaft thrust bearing was relocated to the
Wholesale China Custom Plastic Injection Suppliers - YakonMold frequencies to the transmission and driveline.
OEM China Double Color Injection Mould OEM/ODM Quotes - YakonMold
OEM China Double Color Injection Mould Wholesaler - YakonMoldOEM China Double Color Injection Mould Exporter - YakonMold from cast aluminium,OEM China Double Color Injection Mould Factory - YakonMold predecessor. To reduce friction,OEM China Double Color Injection Mould Manufacturers - YakonMoldSupply China Custom Plastic Injection Factory - YakonMold OEM China Double Color Injection Mould Suppliers - YakonMold. Other features of
Supply China Double Color Injection Mould Wholesaler - YakonMold-Supply China Double Color Injection Mould Exporter - YakonMold, flat top combustion surfaces
Supply China Double Color Injection Mould Factory - YakonMold.
Supply China Double Color Injection Mould Manufacturers - YakonMold
Supply China Double Color Injection Mould Suppliers - YakonMoldWholesale China Double Color Injection Mould OEM/ODM Quotes - YakonMold Wholesale China Double Color Injection Mould Wholesaler - YakonMold.Wholesale China Double Color Injection Mould Exporter - YakonMold temperature, the air inlet duct received air from outside the under bonnet
area. Furthermore, two resonators were incorporated in the air duct to
‘smooth’ the air flow and a large still air box - mounted on the throttle
chamber -Wholesale China Double Color Injection Mould Factory - YakonMold.
Cylinder head
The Wholesale China Double Color Injection Mould Manufacturers - YakonMold cross-flow cooling.Wholesale China Double Color Injection Mould Suppliers - YakonMold,OEM China Silicone Injection Mould OEM/ODM Quotes - YakonMold OEM China Silicone Injection Mould Exporter - YakonMold‘Supply China Custom Plastic Injection Wholesaler - YakonMold’ motion for air as it entered the
cylinder for better mixing of the air and fuel for more uniform flame travel
and faster combustion.OEM China Silicone Injection Mould Factory - YakonMold,OEM China Silicone Injection Mould Manufacturers - YakonMold for maximum gas pressure (downward force)OEM China Silicone Injection Mould Suppliers - YakonMold-15
degrees ATDC (after top dead centre) when the maximum turning moment on the
crankshaft occurred, thereby increasing power output.
Camshaft and valves
The Supply China Silicone Injection Mould OEM/ODM Quotes - YakonMold-type single overhead camshaft
(SOHC) per cylinder bank. Due to the cylinder head offset, the left camshaft
was longer than the right camshaft to align the cam belt sprockets. Both
camshafts were driven by a single belt which had round profile teeth for
quiet operation and was constructed of wear-resistant double canvas and heat
resistant rubber materials with a wire core. Furthermore, the timing belt
had an automatic tensioner which allowed for thermal expansion and
contraction. The recommended replacement interval for the cam belt was
100,000 kilometres or four years, whichever occurred first.
The
Supply China Silicone Injection Mould Wholesaler - YakonMold roller rocker arms. Valve clearance checking/adjustment was only necessary
every 150,000 kms.
Injection and ignition
The Supply China Silicone Injection Mould Exporter - YakonMold-point sequential fuel injection and
centrally located spark plugs. The Supply China Silicone Injection Mould Factory - YakonMold coils (one for each pair of cylinders, i.e. 1-2 and 3-4) which fired the
spark plugs directly twice per cycle.Supply China Silicone Injection Mould Suppliers - YakonMold ‘fuzzy logic’ that enabled the maximum ignition advanced angle to be used
without detonation since the programme continually adapted to changes in
environmental conditions and fuel quality.
The Wholesale China Auto Parts Making Machine Manufacturers - YakonMold
Wholesale China Silicone Injection Mould Wholesaler - YakonMold.1:1, compared to 9.7:1 for its
Supply China Gray Water Storage Tank Suppliers - Rongdapredecessor.OEM China Silicone Injection Mould Factory - YakonMold, the better air/fuel mixing provided by the
Wholesale China Silicone Injection Mould Exporter - YakonMoldWholesale China Silicone Injection Mould Factory - YakonMold to detonation or pinging, enabling a higher compression ratio.
For
the OEM China Plastic Injection Mould Makers Wholesaler - YakonMold, the injection and firing order was 1-3-2-4.
Wholesale China Silicone Injection Mould Manufacturers - YakonMold/Wholesale China Silicone Injection Mould Suppliers - YakonMold: EJ202 changes
For the
Supply China Cnc Precision Machined Components OEM/ODM Quotes - YakonMoldwhich was introduced in 2003, a number of
OEM China Injection Moulding Parts Wholesaler - YakonMold:
- A lighter cylinder block and head;
- Thinner and lighter cylinder liners;
- A sintered crankshaft journal;
- A re-OEM China Injection Moulding Parts Exporter - YakonMold; and,
- A new 4-2-OEM China Injection Moulding Parts Factory - YakonMold.
